Front Rear Crankshaft Max 88% OFF Seal Wear Compa Sleeve J-35686-B Installer $167,J-35686-B,/branchstand886713.html,mylanguagehub.com,Seal,Front,Crankshaft,Installer,Wear,Sleeve,Rear,Compa,Automotive , Replacement Parts $167 Front Rear Crankshaft Seal Wear Sleeve Installer J-35686-B Compa Automotive Replacement Parts $167,J-35686-B,/branchstand886713.html,mylanguagehub.com,Seal,Front,Crankshaft,Installer,Wear,Sleeve,Rear,Compa,Automotive , Replacement Parts Front Rear Crankshaft Max 88% OFF Seal Wear Compa Sleeve J-35686-B Installer $167 Front Rear Crankshaft Seal Wear Sleeve Installer J-35686-B Compa Automotive Replacement Parts

Front Rear Crankshaft Max 88% OFF Seal Cheap mail order sales Wear Compa Sleeve J-35686-B Installer

Front Rear Crankshaft Seal Wear Sleeve Installer J-35686-B Compa

$167

Front Rear Crankshaft Seal Wear Sleeve Installer J-35686-B Compa

|||

Product Description

Diesel Front amp; Rear Crankshaft Seal/Wear Sleeve Installer Diesel Front amp; Rear Crankshaft Seal/Wear Sleeve Installer

Instruction:

  • 1. Lubricate the rubber outer diameter of the oil seal with clean engine oil. Lubricate the gear case cover or flywheel housing bore with clean engine oil.
  • 2. Install two guide studs (J–35686–2) through the holes provided in the center guide assembly (J–35686–1) and into two of the tapped holes in the crankshaft 180 degrees apart. Tighten the guide studs. The base must be tight against the end of the crankshaft.
  • 3. Install the spacers to the center screw of the base.
  • 4. Slide the oil seal assembly over the installer base as far onto the crankshaft hub as possible. Slide collar with the stepped side contacting the seal. Slide the installer cup over the guide studs and installer base.
  • 5. Lubricate the center screw of the base with extreme pressure lubricant. Install the thrust bearing with the case side toward the installer cup and install the hex nut to the center screw of the base.
  • 6. Tighten the hex nut until the oil seal and wear sleeve are pressed into the flywheel housing or gear case cover.
  • 7. When the inside surface of the housing is seated firmly against the base and spacers the seal and sleeve are properly installed.
Front/Rear Crankshaft Seal Wear Sleeve Installer/Caterpillar Front/Rear Crankshaft Seal Wear Sleeve Installer/Caterpillar

Features:

  • 1) Meterial: Premium grade wear-resistant steel structure with black oxide finish, durability, anti-corrosion and anti-rust. High precision and hardness to provide a much longer service life.
  • 2) This tool is easier to use due to a simpler design. Protect your engine by preventing wear sleeve lip flare by using our low-priced but quality installation tools.
  • 3) Installs the front and rear crankshaft wear sleeves and seals. It eliminates lip flare on the wear sleeve and installs the seal properly.
  • 4) Prevent seal leakage.
  • 5) For use on Detroit Diesel Series 60 and two cycle 92.
  • 6) Similar to J-35686-B.
  • 7) Installs front crankshaft seal.
  • 8) Installs front crankshaft wear sleeve.
Front and Rear Crankshaft Oil Seal Wear Sleeve InstallerFront and Rear Crankshaft Oil Seal Wear Sleeve Installer

Package list:

  • 1 set of Front and Rear Crankshaft Seal Wear Sleeve Installer

Front Rear Crankshaft Seal Wear Sleeve Installer J-35686-B Compa


  • Best of The Rolling Stones

    Diverging from the pop rock of the early 1960s, the Rolling Stones pioneered the gritty, heavier-driven sound that would come to define hard(er) rock....

  • A Seasonal Homage to Millennial Music History

    "Summer, summer, summertime, time to sit back and unwind." What the 1991 hit by DJ Jazzy Jeff & The Fresh Prince may lack in profundity is more than made...

  • July Birthdays

    From stars and stripes to Ringo Starr and Jack White of The White Stripes, July is chock-full of birthday celebrations. To commemorate the season in quintessentially...